|
How to Make a Simple, Sturdy,
Low Cost, RC Boat Stand
By Ralph von Eppinghoven
Metro Marine Modelers Toronto, Canada
For a hard copy of this article you can
download the PDF version and print it out.
Sturdy boat stands are a must for every fast electric R.C. boater.
There are lots of ways to build them, but most are time consuming
and tricky to build right. This article describes a technique that
uses plastic foam packing blocks to make custom boat stands in about
30 minutes, at almost no cost! It is fast and easy and allows
builders to spend time building boats, instead of stands!
1. REQUIRED MATERIALS:
One of the best things about these boat stands is that they cost
almost nothing to make. The key materials are surplus plastic foam
packing blocks that are commonly used to ship electronics, or other
fragile items in cartons. Step 1 shows the various types of plastic
foam packing blocks that are available. Again, these are simply
packaging materials, so they are surplus and are often discarded
with the cartons. These surplus blocks can be obtained at any
factory, warehouse, equipment distributor, or retail electronics
store once they are finished unpacking their goods. It should be
noted that these are not common Styrofoam blocks. Styrofoam can be
used, but this material is a stronger, more flexible type of plastic
foam that stands up better to the wear and tear that the boat stand
will undergo.
Step 1: Obtain plastic foam shipping blocks Step
2: Cut selected material
to desired shape
2. ASSEMBLING THE BASE SHAPE:
Once the foam block(s) has been selected, it may be necessary to cut
the blocks to the desired size of base for the boat stand. The size
of the base is determined by the overall length and width of the
boat hull. Basically, cut the foam blocks and re-assemble them to
form a rectangular base that is about 2” wider than the hull (if
possible) and about ¾ of the overall length of the hull, excluding
running hardware. It may be necessary to stack the blocks one on top
of another to make the base tall enough to hold the hull and provide
enough height for the rudder not to be touching the ground. The
easiest way to cut the foam blocks is to use a serrated edge knife,
such as a common bread knife. Step 2 shows the blue foam packing
block cut apart and re-assembled to form a rectangular base. Note
the two layers of blocks at the front, middle, and rear of the base
that will provide the required height to support the hull.
Of course, in some instances it may be possible to find a foam block
that already has the rectangular dimensions required for the base of
the boat stand. In that case, proceed directly to Step 4.
3. GLUING THE BOAT STAND PIECES:
After the foam pieces have been cut to size, they must be glued
together to form a rectangular base. The simplest and quickest way
to do this is to use a hot glue gun and apply the hot glue to the
foam pieces and assemble the blocks. This is very quick since the
glue sets immediately after it has cooled down. If a hot glue gun is
not available, construction adhesives used for Styrofoam wall
insulation can be used. These glues typically set overnight so it is
a slower process. Step 3 shows the assembled rectangular boat stand
base.
Step 3: Glue foam blocks together Step 4: Trim
stand to fit mono or hydro hull
using hot glue gun
4. TRIMMING THE SHAPE OF THE BOAT STAND:
Once the rectangular base has been built, it is necessary to trim
the blocks to fit the shape of the hull. An easy way to do this is
to make a paper template of the shape of the transom and tape this
to the rear of the stand. Then trim the base to the shape of the
temple using the serrated knife. The front of the boat stand needs
to be trimmed to match the curve of the hull. This typically means
making the trimmed “vee” narrower at the bow end relative to the
stern end of the boat stand. The trimming process usually takes a
few cuts to get the shape just right. Be careful not to remove too
much material – it is easier to trim off more than re-glue a removed
piece. Step 4 shows the trimmed stand for a large monohull model. It
is recommended to trim the corners off the front of the stand to
make is easy to know which end is the bow end. Steps 5 and 6 show
the finished boat stand for the monohull. Note the snug fit of the
hull into the stand and the required clearance for the rudder.
Step 5: Hull securely supported by stand Step 6: Ensure proper
height for rudder/strut
If the boat stand is for a hydroplane model, the trimming is usually
easier since the hydro has a flat bottom. The trimming usually
consists of cutting the width of the foam base to match the sponson
width at the bow and the transom width at the stern of the boat
stand. Step 7 shows various FE boats and the different types of foam
block boat stands used to support them.
Step 7: A fleet of FE boats all safely riding in their foam boat
stands
Go ahead and experiment with different shapes and sizes of foam boat
stands. They are easy to make and cost almost nothing, so give them
a try.
|
