Rubycon Low ESR Capacitor

Good for use with up to 6s esc's. See forum for install and applications.
Rubycon part number: 35ZLH1000M12.5X20

Specs:
Rated Voltage: 35v   Rated Capacitance: 1000uF
Capacitance Tolerance: 20%
Temperature Range: -40 to 105C
Rated Ripple Current: 2480
12.5mm diameter x 20mm height

WARNING: If any capacitors seem to bulge, start to deform, leak or pop, stop using them IMMEDIATELY!!! If Capacitors fail they can explode and cause injury.

It is generally reported that capacitor failures can be attributed to:
1) Heating, causing a capacitor to swell and explode.
2) Drying of the liquid electrolytic inside from various causes, such as defects, leaking and even cleaning.
3) Capacitors re-form over time to meet a usual and expected voltage. Surges that are not normal can cause sudden failure.
4) The older they get the greater the incidence of failure.
5)High-current motor setup will tend to kill the caps quickly (because of the large voltage changes).

Click picture for more info.


Hobby Wing "SeaKing" 35 Amp ESC.
 
This is boat model, specially designed for boat use with water-cooling system and the esc is water resistant.

Features:
Compatible with all sonsorless brushless motor.
Use top quality electronic components to enhance the current endurance ability of the ESC.
Excellent start-up, acceleration and linearity features.
With 2 running modes (Racing mode and Forward/Backward mode).
With 4 steps of maximum reverse force adjustment.
Proportional ABS brake function with 4 steps of maximum brake force adjustment, 8 steps of drag-brake force adjustment and 4 steps of initial brake force adjustment.
With 4 start modes (Also called "Punch" ) from "Soft" to "Very aggressive".
Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / Throttle signal loss protection / Motor blocked protection.
With 8 steps of timing adjustment to get the best compatibility with various of motors.
Easily program with only one button and compatible with optional program card.
Built in BEC(battery eliminator circuit).

Click picture for more info.

Hobby Wing "SeaKing" 60 Amp ESC.
 
This is boat model, specially designed for boat use with water-cooling system and the esc is water resistant.

1 Use top quality electronic components.
2 Special designed for RC boat, with excellent start-up, acceleration and linearity features.
3 With water cooling system and the whole ESC is waterproof to get a longer life.
4 With 2 running modes ("Forward" mode and "Forward/Backward" mode).
5 Low voltage cut-off protection for lithium or nickel battery
6 Over-heat protection.
7 Throttle signal loss protection. 
8 With 8 steps of timing adjustment, compatible with sensorless brushless motors.
9 Swtching mode built-in BEC uptp 6 cells lipo battery.
10 User programmable and compatible with HobbyWing LED Programmer.

Click picture for more info.

Hobby Wing "SeaKing" 120 Amp ESC.
 
This is boat model, specially designed for boat use with water-cooling system and the esc is water resistant.

-Use top quality electronic components.
-Special designed for RC boat, with excellent start-up, acceleration and linearity features.
-With water cooling system and the whole ESC is waterproof to get a longer life.
-With 2 running modes ("Forward" mode and "Forward/Backward" mode).
-Low voltage cut-off protection for lithium or nickel battery
-Over-heat protection.
-Throttle signal loss protection. 
-With 8 steps of timing adjustment, compatible with sensorless brushless motors.
-Swtching mode built-in BEC uptp 6 cells lipo battery.
-User programmable and compatible with HobbyWing LED Programmer.

Click picture for more info.

Hobby Wing "SeaKing" 90 Amp ESC.
 
This is boat model, specially designed for boat use with water-cooling system and the esc is water resistant.

-Use top quality electronic components.
-Special designed for RC boat, with excellent start-up, acceleration and linearity features.
-With water cooling system and the whole ESC is waterproof to get a longer life.
-With 2 running modes ("Forward" mode and "Forward/Backward" mode).
-Low voltage cut-off protection for lithium or nickel battery
-Over-heat protection.
-Throttle signal loss protection. 
-With 8 steps of timing adjustment, compatible with sensorless brushless motors.
-Swtching mode built-in BEC uptp 6 cells lipo battery.
-User programmable and compatible with HobbyWing LED Programmer.

Hobby Wing "SeaKing" 180 Amp ESC.

This is Version 3 with added Capacitor Bank.
 
This is boat model, specially designed for boat use with water-cooling system and the esc is water resistant.

Special designed for RC boat, with excellent start-up, acceleration and linearity features.
With 2 running modes ("Forward" mode and "Forward/Backward" mode). Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / Throttle signal loss protection. With 8 steps of timing adjustment, compatible with all kinds of sensorless brushless motors. Swtching mode built-in BEC has a very powerful output even working with 6 cells lipo battery. User programmable and compatible with the pocket-sized Digital LED Program Card (Optional equipment) to set the ESC easily.

Click picture for more details.

Hobby Wing "SeaKing" 180 Amp ESC.

Output: Continuous amps 130, burst amps 180.
Input: 15-36 cells NiMH/NiCd or 5-12 LiPo.
BEC Output: No Built-in BEC.
Suitable Motor: Sensorless Brushless Motor.
Water Cooling Pipe: 5.0mm(external diameter)
Size: 88mm(L)*58mm(W)*23mm(H).
Weight: 182g

Click picture for more details.

Digital Program box for SeaKing Marine Esc's. Programs Seaking 60, 90, 120, 130HV and 180 amp esc's.

Allows for quick and easy programing without needing to use the transmitter.

Programs the following parameters:
1)Forward/Forward & Reverse.
2)Number of cells(Auto or Select your own Cell Count)
3)Low Voltage Cutoff, Program Cutoff Voltage (No Cutoff, 2.8, 3.0v, 3.2v, 3.4v)
4)Timing (0.0, 3.75, 7.5, 11.25, 15.0, 18.25, 22.0, 26.25

Pro Boat’s new waterproof marine electronic speed control is definitely one of the best new values in model boating. Anyone can upgrade their RTR boat from a mechanical speed control to the precision of a fully proportional ESC with reverse.

Discontinued, replaced by Swordfish 120+ with data logging.
Click for new version.

Hifei Swordfish 120 amp water cooled esc. This is a high quality ESC designed specifically for racing boat. Unique PCB layout allows the water cooling plate to cool both fet boards evenly. Programing can be done with your transmitter or optional program card, optional USB adapter or optional LCD Program Box/Handheld Unit.

6-20 NiCad/NiMh cells or 2s to 6s LiPo. This unit is water resistant.

Click picture for more info.

Hifei Swordfish 120+ ESC, is a high quality ESC which is specially designed for racing boats with a built in data logger. Unique PCB layout between the drive boards and water cooler keep the ESC cool at all times. The extremely low resistance (0.00066 ohm) and up to 8 optional program setting make your power system incredible. Programing can be done with your transmitter, optional program card, optional USB adapter or optional LCD Program Box/Handheld Unit.

The data logger will record current/amps, pack voltage, RPM, ESC Temperature and throttle position. Optional USB adapter required.

6-20 NiCad/NiMh cells or 2s to 6s LiPo. This unit is water resistant.

Click picture for more info.

Hifei Swordfish 200+ ESC, is a high quality ESC which is specially designed for racing boats with a built in data logger. Unique PCB layout between the drive boards and water cooler keep the ESC cool at all times. The extremely low resistance and up to 8 optional program setting make your power system incredible. Programing can be done with your transmitter, optional program card, optional USB adapter or optional LCD Program Box/Handheld Unit.

The data logger will record current/amps, pack voltage, RPM, ESC Temperature and throttle position. Optional USB adapter required.

6-20 NiCad/NiMh cells or 2s to 6s LiPo. This unit is water resistant.

Discontinued, replaced by Swordfish 200+ with data logging. Click here for Info

Hifei Swordfish 200 amp water cooled esc. This is a high quality ESC designed specifically for racing boat. Unique PCB layout allows the water cooling plate to cool both fet boards evenly. Programing can be done with your transmitter or optional program card, optional USB adapter or optional LCD Program Box/Handheld Unit.

6-20 NiCad/NiMh cells or 2s to 6s LiPo. This unit is water resistant.

As of 8/16/2011 these come with a second cooling plate.

Discontinued. Replaced by Swordfish Pro 240hv.
Click here for new version.

Hifei Swordfish 240 amp high voltage water cooled esc. This is a high quality ESC designed specifically for racing boat. Programing can be done with your transmitter, optional program card or optional USB adapter or optional LCD Program Box/Handheld Unit.

Up to 38 NiCad/NiMh cells or 3s to 12s LiPo. This unit is water resistant.

As of July 2010, these come with 8 gauge wires.

Click picture for more details

At a maximum of 300 amps and 60 volts, this is the most powerful esc that Hifei has ever produced. Able to provide power upto a 30 Horse Power Electric Motor!!! And with the new data logging feature, you will be able to take the guess work out of prop, motor or strut changes by logging the following info, Current/Amps, Voltage, Temperature, RPM, Power & Throttle travel.

Basic Specs:
- Features a metal case to function as a heat sink and water proof box for the circuitry!
- 48cells NiMH/NiCad or 4 to 15 cell Lithium-polymer
- 300A continous (380A surge)

Click picture for more info.

Hifei Swordfish Pro 240 amp high voltage water cooled esc. This is a high quality ESC designed specifically for racing boat. Programing can be done with your transmitter, optional program card or optional USB adapter or optional LCD Program Box/Handheld Unit.

Up to 38 NiCad/NiMh cells or 4s to 12s LiPo. This unit is encased in rubber, making it very water resistant.

ETTI Race 150 Brushless ESC with Battery Eliminator Circuit (BEC).
7.2 volts to 24 volts ( 2-5 lipo / 6-16 NiMH). 150 amp constant Electronic Speed Control(ESC) by ETTI. This is a water resistant esc with water cooling for Fast Electric rc boaters.

Add a Etti E035 35 volt Capacitor Bank for Only 15.00 more! A $10 savings!

Specs:
Weight: 100g, 120g with wires.
Wire gauge: 10 gauge battery side : 12 gauge motor side.
Dimension: 95x50x13mm
Amp rating: 150A Continuous : 300A Quick burst
Battery type: 2-5 Li-Po or 6-16 Ni-MH/Ni-Cd (Low volt cut off per cell)
BEC: YES
IR: 0.00076Ω
Aluminum Water Cooling Plate 
Temperature Overloads Protection: 90 °C 
Suggested Timing: 1° (2-4 poles motor) : 7° (6-8 poles motor) : 15° (10-14 poles motor) : 30° (10-14 poles motor)

ETTI Race 150 Brushless ESC 7.2volts to 30 volts ( 2-7 lipo / 6-20 NiMH). 150 amp constant Electronic Speed Control(ESC). This is a water resistant esc with water cooling for Fast Electric rc boaters.

Add a Etti E035 35 volt Capacitor Bank for Only 15.00 more! A $10 savings!

Specs:
Weight: 100g, 120g with wires.
Wire gauge: 10 gauge battery side : 12 gauge motor side.
Dimension: 95x50x13mm
Amp rating: 150A Continuous : 300A Quick burst
Battery type: 2-7 Li-Po or 6-20 Ni-MH/Ni-Cd (Low volt cut off per cell  )
BEC: No
IR: 0.001Ω
Aluminum Water Cooling Plate 
Temperature Overloads Protection: 90 °C 
Suggested Timing: 1° (2-4 poles motor) : 7° (6-8 poles motor) : 15° (10-14 poles motor) : 30° (10-14 poles motor)

NEW FROM ETTI Marine!!!

Etti High Voltage 120A Opto PRO II Navy Competition Brushless ESC for up to 60 Volts.

Specs:
12 - 60 V
10 - 40 Cells NiMH
4 - 14 Cells LiPo
120 Amp Current
Battery eliminator circuit (BEC): NO
Resistance: 0.002 £
Size: 100x65x13mm
Weight: 145g (including wires)
(Ultra Low Resistance Version)

This is a water resistant esc with water cooling for Fast Electric rc boaters.

Requires:
Connectors for both the motor and batteries. We suggest 5.5mm, 6.0mm or 8.0mm bullet connectors. Has no bec, so this will require an external battery eliminator circuit or a battery pack to power your receiver.

NOTE: Pictures 2 and 3 show the esc with an attached capacitor board. The board is included but not installed. This is for example placement/installation purposes only.
 

NEW FROM ETTI Marine!!!

Etti High Voltage 220A Opto PRO II Navy Competition Brushless ESC for up to 60 Volts.

Specs:
Voltage: 12 - 60 V
NiMH: 10 - 40 Cells
LiPo: 4 - 14 Cells
Current: 220 Amp
Battery Eliminator Circuit(BEC): NO
Resistance: 0.001 £
Size: 100x65x22mm
Weight: 315g (including wires & HV Cap's Module)
(Ultra Low Resistance Version)

This is a water resistant esc with water cooling for Fast Electric rc boaters.

Requires:
Connectors for both the motor and batteries. We suggest  8.0mm OSE or Castle Creations bullet connectors.
Has no bec, so this will require an external battery eliminator circuit or a battery pack to power your receiver.

NOTE: Pictures 2 and 3 show the esc with an attached capacitor board. The board is included but not installed. This is for example placement/installation purposes only.

150A Power Analyzer. This logger can analyze the Battery condition, capacity, current draw, motor rpm and the run time of your boat in the water and on the bench. This will make setup of your boat an easier task without guessing. This has a maximum amp draw of 150 amps, Max 26 volts.

Power Analyzer Manual ( Power Analyser(EN).pdf )

Power Analyser-Portable LCD Operation Pane Manual(EN) ( Power Analyser-Portable LCD Operation Panel(EN).pdf )

This is fully compatible with the Etti 45a Navy, Etti 70a Navy, Etti 90a Navy, Etti Race 150, Etti Race 150 bec. At this time this can not be used with the HV100.

This can also be used with other esc's to log voltage, current and other functions, but the rpm will not be logged.

Click picture for more info.

Castle Creations Mamba Max Pro Speed Control.

ROAR legal for 1/10 scale applications.Including Namba N1 mono and N1 Hydro. Using this esc in the sensored mode, the esc can increase rpm allowing stock brushless motors to be run in n1 classes as very fast speeds.

Runs in sensored and sensorless motor operating modes.
Handles up to 6S LiPo input.
Switching BEC provides power for servo and receiver all the way to 6S

Castle Creations Hydra Ice 240

240 Amps. 8s Lipo with built in BEC & data logging.
The controller actually measures and records parameters such as battery volts, amp draw, motor rpm, controller temperature and battery ripple voltage. This is a great way to make sure that the entire setup is performing within limits. Data may be read from the controller after a run using the Optional* Castle Link USB adapter (Windows PC Required) running the free Castle Link software.

Max volts: 8s Lipo (33.6 volts fully charged LiPos).
Brake: Proportional
Reversible: Yes - with lockout
Low voltage cutoff: Programmable - Auto LiPo Detect set as default
Size: 3.9" L x 1.6" W x 1.6" H (102mm x 51mm x 41mm) - all measurements made without cooling tubes.
Weight: 4.9 oz. (140g) without wires, 7.8 oz. (222g) with wires
Controller type: Sensorless only
Cooling: Aluminum cooling tubes integral with controller's heat sink. User must supply flexible watter supply tubing.
BEC: 5 amps, 5v output

Castle Link compatible: Yes. Requires Optional Castle Link USB adapter and Castle Link PC software.

Castle Creations Hydra Ice 2 200HV ESC

This is Version 2 of the Castle Ice Series ESC. Includes data logging.
The controller actually measures and records parameters such as battery volts, amp draw, motor rpm, controller temperature and battery ripple voltage. This is a great way to make sure that the entire setup is performing within limits. Data may be read from the controller after a run using the Optional* Castle Link USB adapter (Windows PC Required) running the free Castle Link software.

200 Amps at 50 Volts
Max volts: 12s Lipo (50.4 volts fully charged LiPos).
Brake: Proportional
Reversible: Yes - with lockout
Low voltage cutoff: Programmable - Auto LiPo Detect set as default
Size: 3.9" L x 1.6" W x 1.6" H (102mm x 51mm x 41mm) - all measurements made without cooling tubes.
Weight: 4.9 oz. (140g) without wires, 7.8 oz. (222g) with wires
Controller type: Sensorless only
Cooling: Aluminum cooling tubes integral with controller's heat sink. User must supply flexible watter supply tubing.
BEC: No BEC.
Castle Link compatible: Yes. Requires Optional Castle Link USB adapter and Castle Link PC software.

This is a much simpler way to program your Castle Brushless esc's. Once installed programming will take a matter of seconds!! Rather than having to use the remote control and go through a sequence of trigger pulls.

Click picture for more details.

This is the Castle Link Quick Connect from Castle Creations.

FEATURES: Installs between ESC and receiver Y-harness with wire to connect to Castle Link. This can be left connected for easy access for Castle Link USB Programer without disrupting receiver or ESC Detects the presence of Castle Link USB Programer/adapter.

These are meant to cool the AquaCraft Aqum7010 ESC that comes stock with the AquaCraft SuperVee 27.

Each cooling plate has a cooling area approximately of 35mm x 40mm

Click picture for full details.

This is the AquaCraft Marine 45 Amp Brushless Electronic Speed Control.
                      
Water-cooled aluminum case with built in water cooling and waterproof. With built in BEC (battery eliminator circuit).

This is a plug in play unit when combined with the Stock Super Vee 27 or Stock SuperVee 27R

NOTE: This is not Lipo Ready. Requires external low voltage cutoff to work with lipo packs. 

AquaCraft UL-1 ESC, now updated with larger capacitor!

This is the 8-20 volt - 60 Amp Marine Lipo Ready Electronic Speed Control from AquaCraft. This is the stock ESC for the Ul-1 superior Hydro. But can be used with many other brushless motors.

Waterproof and Water cooled aluminum case with installed Deans Ultra plugs. Stutter bump warning system.

45-Amp Brushless ESC

Stock replacement speed control for the ProBoat Brushless BlackJack 26

Specs:
-Forward:Yes
-Brake:Yes
-Continuous Maximum Current:45A
-Input Voltage:Minimum 10V, Maximum 21V
-Momentary Peak Current:55A
-BEC Voltage:5.8V

60-Amp Brushless ESC

Stock replacement speed control for the ProBoat Brushless Stiletto Tunnel Hull. Comes with installed 3.5mm female bullet connectors for the motor end and two deans connectors for the battery end.

Specs:
-Forward Only:Yes
-Continuous Maximum Current:60A
-Input Voltage:Minimum ?, Maximum ?
-Momentary Peak Current: ?
-BEC Voltage: 5.8V

Bruslesss ESC Programming Module for PRB3309 or PRB4018. These are the esc's that come stock in the following brushless boats, BlackJack, Impulse, Geico, Mystic and Stiletto.

If brushless power alone isn’t enough to satisfy your need for speed, the Pro Boat Brushless Programming Module is what you need to take advantage of the latest Li-Po battery technology. The programming module allows you to program the ProBoat brushless speed control for safe use of Li-Po batteries, with settings for voltage cutoff, brake function, timing, throttle curve and more.

Key Features:

-Settings for battery type (Li-Po or Ni-MH)
-High or low voltage cutoff
-Adjustable brake, timing and throttle curve

Programs these esc model numbers PRB3309 or PRB4018 esc's.

Requires:
Only the esc you need programed.

This is the Great Planes Deans Ultra Parallel ESC to Single battery Pack. This can be used with 2 esc's that will draw no more than 30 amps each.

1 Male to 2 Female Adapter.

SPECS:
Maximum Recommended Continuous Current: 60A

Aluminum water cooling plate for Electronic Speed Controls. Anodized in red color.

42mm Long x 32mm Wide x 7mm Thick

Weights approximately 20 grams.

Note! This is the aluminum plate only.

Aluminum water cooling plate for Electronic Speed Controls. Anodized in Orange Color.

30mm Long x 22mm Wide x 6mm Thick

Weights approximately 11 grams.

Note! This is the aluminum plate only.

Aluminum water cooling plate for Electronic Speed Controls. Anodized in orange color.

42mm Long x 25mm Wide x 6mm Thick

Weights approximately 17 grams.

Note! This is the aluminum plate only.

Aluminum water cooling plate for Electronic Speed Controls.

40mm Long x 38mm Wide x 6mm Thick

Weights approximately 1/2 ounce.

Note! This is the aluminum plate only. Esc in picture is just for reference.

Want to use a inexpensive airplane esc for your rc boat or car? This is the product for you!! This module will allow an airplane esc that is designed to work with a stick style transmitter to work with a pistol style transmitter.

Adapter Board Measures approx. .50" x .75". Wire measures approx 3" long

Click picturs for more details.

LipoShield low voltage cutoff (LVC) device.

These are programmed with a cutoff of 3.2volts. This device enables both New esc's & older ESC’s with no low voltage cutoff built into them to be used with lithium battery packs. It can also be used with esc’s that have unreliable low voltage cutoffs. It installs easily between your receiver and ESC and provides a reliable 3.2V per cell soft cutoff to prevent over-discharge damage to your expensive lipo packs. This is for esc’s with forward only throttle.

Click here to download instructions,
www.dimensionengineering.com/datasheets/LipoShield.pdf

Click picture for more details.

Sport BEC by Dimension Engineering.

So you want to be free of the pains of running a Receiver (RX) battery pack? Tired of having a dead receiver pack ruin your day? Tired of buying AA batteries to power your receiver? Need to shed some weight from your Fast Electric? If you answered yes to any of those 3 questions this BEC (battery eliminator circuit) product is for you. It uses your motor battery pack to supply power to your receiver. At only 13 grams and 1.0" long this will fit almost anywhere!
 

Castle Creations BEC, RX Battery Eliminator. 

Are you running a receiver pack or having it die in the middle of the lake? If Yes read on.

Tired of having a dead receiver pack ruin your day?
Tired of buying AA batteries to power your receiver? Need to shed some weight from your Fast Electric? If you answered yes to any of those 3 questions click the picture for more details. 

UBEC for 2-5s Lipo.

●The UBEC is an advanced switching regulator, provides over-current and over-heat protection function, and the witching frequency is 300KHz.The max efficiency of this chip is 92%
●The smallest size and the lightest weight make it convenient to use.
●The comparison of linear BEC and switch-mode BEC: When using a lithium battery pack more than 3S, a switch-mode BEC has much higher efficiency than linear BEC.

Click picture for more details.

Castle Creations PRO High Output Battery Eliminator Circuit(BEC). 

FEATURES: Ideal for use in larger RC cars, electric aircraft, and electric helis 500 size and larger that have high power demands for their radio system Also works well in larger electric powered RC aircraft and RC crawlers and monster trucks that use high powered servos

INCLUDES: CC BEC Pro High Output Switching BEC with connectors and instruction sheet

Stand alone programming box for the Hefei Swordfish Esc's. Large lcd readout makes for quick and easy option programing without the need of a computer.

Note: When using this with the 240HV Esc. You will also need a 4cell AA receiver pack to power the programmer. Otherwise the esc's with bec will supply power to the programmer. 

Stand alone programming card for the Hefei Swordfish Esc's. Allows quick and easy option programing without the need of a computer.

Note: When using this with the 240HV Esc. You will also need a 4cell AA receiver pack to power the programmer. Otherwise the esc's with bec will supply power to the programmer. 

USB interface adapter for the Hefei Swordfish Esc's. This is needed to program the Swordfish esc's on your pc.

Note: Software install requires Microsoft Windows and a very good understanding of installing drivers and changing settings in Windows. Please purchase the Program Box if you are not up to making these changes. 

When using this with the 240HV Esc. You will also need a 4cell AA receiver pack to power the programmer. Otherwise the esc's with bec will supply power to the programmer. 

Castle Creations Capacitor Pack.

Recommended for up to 12s Maximum.

It is generally reported that capacitor failures can be attributed to:
1) Heating, causing a capacitor to swell and explode.
2) Drying of the liquid electrolytic inside from various causes, such as defects, leaking and even cleaning.
3) Capacitors re-form over time to meet a usual and expected voltage. Surges that are not normal can cause sudden failure.
4) The older they get the greater the incidence of failure.
5)High-current motor setup will tend to kill the caps quickly (because of the large voltage changes).

Etti Capacitor Bank for Brushless Esc's

35 volt Capacitors. Recommended for up to 7s Maximum.

It is generally reported that capacitor failures can be attributed to:
1) Heating, causing a capacitor to swell and explode.
2) Drying of the liquid electrolytic inside from various causes, such as defects, leaking and even cleaning.
3) Capacitors re-form over time to meet a usual and expected voltage. Surges that are not normal can cause sudden failure.
4) The older they get the greater the incidence of failure.
5)High-current motor setup will tend to kill the caps quickly (because of the large voltage changes).

WARNING: If any capacitors seem to bulge, start to deform, leak or pop, stop using them IMMEDIATELY!!! If Capacitors fail they can explode and cause injury.

Hifei Capacitor Bank for Brushless Esc's

63 volt Capacitors. Recommended for up to 12s Maximum.

It is generally reported that capacitor failures can be attributed to:
1) Heating, causing a capacitor to swell and explode.
2) Drying of the liquid electrolytic inside from various causes, such as defects, leaking and even cleaning.
3) Capacitors re-form over time to meet a usual and expected voltage. Surges that are not normal can cause sudden failure.
4) The older they get the greater the incidence of failure.
5)High-current motor setup will tend to kill the caps quickly (because of the large voltage changes).

Hifei Capacitor Bank with 8mm Bullet Connectors & Anti Spark Point for Brushless Esc's.

This capacitor board was designed to make simplify the installation of esc's with 2 sets of battery wires. Simply solder the two sets of esc wires to the capacitor board tabs(see second picture). The solder the included 8mm plugs to your batteries.

63 volt Capacitors. Recommended for up to 14s Maximum.

It is generally reported that capacitor failures can be attributed to:
1) Heating, causing a capacitor to swell and explode.
2) Drying of the liquid electrolytic inside from various causes, such as defects, leaking and even cleaning.
3) Capacitors re-form over time to meet a usual and expected voltage. Surges that are not normal can cause sudden failure.
4) The older they get the greater the incidence of failure.
5)High-current motor setup will tend to kill the caps quickly (because of the large voltage changes).

WARNING: If any capacitors seem to bulge, start to deform, leak or pop, stop using them IMMEDIATELY!!! If Capacitors fail they can explode and cause injury.

Instructions for Anti Spark Point: First, to connect battery negative connector to negative connector on the board, then put battery positive battery connector on the anti-spark point for 3 to 5 seconds, then immediately plug battery positive connector to positive connector on the board.

Hifei Capacitor Bank with 8mm Parallel Bullet Connectors & Anti Spark Point for Brushless Esc's.

This capacitor board was designed to make simplify the installation of esc's with 2 sets of battery wires. Simply solder the two sets of esc wires to the capacitor board tabs(see second picture). The solder the included 8mm plugs to your batteries.

63 volt Capacitors. Recommended for up to 14s Maximum.

It is generally reported that capacitor failures can be attributed to:
1) Heating, causing a capacitor to swell and explode.
2) Drying of the liquid electrolytic inside from various causes, such as defects, leaking and even cleaning.
3) Capacitors re-form over time to meet a usual and expected voltage. Surges that are not normal can cause sudden failure.
4) The older they get the greater the incidence of failure.
5)High-current motor setup will tend to kill the caps quickly (because of the large voltage changes).

WARNING: If any capacitors seem to bulge, start to deform, leak or pop, stop using them IMMEDIATELY!!! If Capacitors fail they can explode and cause injury.

Instructions for Anti Spark Point: First, to connect battery negative connector to negative connector on the board, then put battery positive battery connector on the anti-spark point for 3 to 5 seconds, then immediately plug battery positive connector to positive connector on the board.

Etti Capacitor Bank for High Voltage 63V 5000u.
 Power Cap's Module is specially designed for SAW racing and increase the power of ESC. Equipped with 5 x RUBYCON 63V, 1000u RX 30 Series 130 ¢J Capacitors

Recommended for up to 14s Maximum.

WARNING: If any capacitors seem to bulge, start to deform, leak or pop, stop using them IMMEDIATELY!!! If Capacitors fail they can explode and cause injury.

It is generally reported that capacitor failures can be attributed to:
1) Heating, causing a capacitor to swell and explode.
2) Drying of the liquid electrolytic inside from various causes, such as defects, leaking and even cleaning.
3) Capacitors re-form over time to meet a usual and expected voltage. Surges that are not normal can cause sudden failure.
4) The older they get the greater the incidence of failure.
5)High-current motor setup will tend to kill the caps quickly (because of the large voltage changes).