Made For cutting of soft material and light gauge wire, these cutters will leave a near finished cut edge.

4" Wide magnetic parts tray. Works great to hold small parts from rolling off your work area. The magnetic base holds the tray to metal steel surfaces and also doubles to hold magnetic items from falling out of it.

Polished stainless steel construction with Oil and fuel resistant rubber coated magnet to prevent marring surfaces. 

The Ofna Pro Nitro Starter Kit combo pack comes complete with a 500cc Fuel Bottle, 1700mah Glo-Plug starter w/ Charger, 2 Extra Glow Plugs, and a 4-Way wrench. As a bonus a long slotted screw driver also included to help adjust your carb! This is one of the best starter kits on out there at this price its a steal!

This is a very useful tool in building a quality built boat.

Cen-Tech 6" Digital Calipers. Free Extra Battery

Metric and SAE digital display
Accurate to 0.001"
Resolution: 0.0005"
Fluid-resistant stainless steel frame, precision ground jaws
On/off switch with automatic shut off

Includes (1) Free Extra 1.5V button cell battery

DuraTrax Flashpoint Infrared Temperature Gauge.

Point and click! That's all that it takes to figure out the temperature of your brushless motor, nitro engine, esc or batteries. This is a tool every electric or nitro hobbyist should carry in their tool box!

Etti propeller balancer. Aluminum and stainless steel construction.
Can balance up to a 4.5" propeller!

Includes 3 different adapters to balance the following propellers.

-3/16" propellers.
-1/8" propellers.
-M4 / 4mm threaded propellers.

Aluminum and stainless steel construction.
Can balance a propeller up to 82mm in diameter!

Includes shafts and adapters to balance most of the varieties of props on the market! Eight different sizes in total!
 
Works with the following propeller shaft sizes.

1/8" propellers
3/16" propellers
1/4" propellers
2mm propellers
3mm propellers
4mm propellers
4mm (M4) Threaded propellers.
5mm propellers

*Propeller in picture not included!

This is an Aqua Craft Grim Racer Precision Metal Prop Balancer.

FEATURES: 
Three thumb-screw adjusters with Bubble level centered in wide stance base. Balances almost all metal props upto 80mm in size.

INCLUDES: 
One prop balancer with instruction sheet, O-ring keepers, .187", 1/8", 3/16" and 1/4" shafts

REQUIRES:
Dust mask, Eye protection, Small round file, Small flat file, 220 Wet/Dry sandpaper, Scratch pad (red), Felt tip pen

The Top Flite balancer is an innovative way to balance your aircraft or boat propellers, spinner backplates, car wheels and tires, as well as many other items in the hobby industry.
 

This prop balancer has an extruded aluminum base and two parallel steel rods for the pro shaft to roll on. It comes complete with a leveling screw and three prop shafts (1/4", 3/16" & 1/8") which store within the unit. Basic instructions are included.

REQUIRES:
Dust mask, Eye protection, small files and sandpaper.

Quality anodized handle & replaceable tips.

Set Includes: 1.5mm,  2.0mm and 2.5mm drivers 
 

Quality anodized handle & replaceable tips.

Set Includes: .050",  1/16",  3/32"

.050 Hex driver with quality anodized handle & replaceable tips.

1/16" Hex driver with quality anodized handle & replaceable tips.

5/64" Hex driver with quality anodized handle & replaceable tips.

3/32" Hex driver with quality anodized handle & replaceable tips.

1.5mm Hex driver with quality anodized handle & replaceable tips.

2.0mm Hex driver with quality anodized handle & replaceable tips.

2.5mm Hex driver with quality anodized handle & replaceable tips.

3.0mm Hex driver with quality anodized handle & replaceable tips.

This is a great test tool to find how many amps your system is drawing or testing cells and much, much more. It connects between the battery pack and load to measure volts, amps, watts and amp hours.

Sale while supplies last! $59.99

Click the picture for full details, specs & requirements.

This is the New Eagle Tree USB Micro Power V3 E-Logger. If your looking for the optimum prop for your boat or gearing for your car, than this is the product for you. With this logger will be able to graph(computer required) voltage and amperage curves! The new v3 supports the optional gps sensor, so you can now tell the speeds of your model.

Logs pack current to 100amps and voltage
to 70 volts.

Sale while supplies last! $59.99

Click picture for full details.

This is the New Eagle Tree USB Micro Power V3 E-Logger with Deans Compatible connectors. If your looking for the optimum prop for your boat or gearing for your car, than this is the product for you. With this logger will be able to graph(computer required) voltage and amperage curves! The new v3 supports the optional gps sensor, so you can now tell the speeds of your model.

Logs pack current to 100amps and voltage
to 70 volts.

Click the picture for full details, specs & requirements.

This is the New High Amp version of the Eagle Tree USB Micro Power V3 E-Logger, good for upto 150 amps! If your looking for the optimum prop for your boat or gearing for your car, than this is the product for you. With this logger will be able to graph(computer required) voltage and amperage curves! The new v3 supports the optional gps sensor, so you can now tell the speeds of your model.

Logs pack current to 150 amps and voltage
to 70 volts.

This is the new GPS V4 Module for the from Eagle Tree Systems.

Key improvements over the V3 Gps expander.
-A faster 10Hz Update Rate versus the old 5Hz.
-Almost 1/2 the cost of the older V3 unit which retailed for $149.99 

Smaller, faster, and more sensitive GPS Expander Module plugs into the system to provide live and/or recorded lat/lon, ground speed, GPS altitude, distance to pilot, course, UTC timestamp, and more. Integrated display/3D graphing software included in data system. WAAS and EGNOS compatible, 10Hz update rate, built-in patch antenna.

Built in LED to indicate 3D Fix.

NO external antenna adapter.

Measures approximately 16mm x 40mm

Requires: Eagle Tree V3

Want to view important data at the pond or tracking without having to drag the laptop? This works with the Eagle Tree Micro Data Logger to display that critical information you need!

Click picture for more details and requirements.

This is the Eagle Tree Brushless RPM Sensor. Simplly plug in one end and solder 2 wires and your done! Works with all versions of the Eagle Tree MicroPower, Seagull Flight Systems and Data Recorder V2 products with firmware version 4.XX

The eLogger V3 supports up to two Hall Effects or Brushless RPM sensors!

This is the Optical RPM Sensor for use with the Data Recorder and MicroPower V2

NEW: The eLogger V3 supports up to two Hall Effects or Brushless RPM sensors!

Requires: Eagle Tree Logger.

Measures RPM to 50K+.  Includes RPM sensor and 4 magnets.

NEW: The eLogger V3 supports up to two Hall Effects or Brushless RPM sensors!

Requires: Eagle Tree Logger.

This is the Micro Temp Sensor for use with the Eagle Tree Data Recorder and MicroPower V2, V3.

NEW: The eLogger V3 supports up to two Hall Effects or Brushless RPM sensors! Up to three temperature sensors can be connected to the eLogger V3 simultaneously (two simultaneously for the V1/V2).

Requires: Eagle Tree Logger.

Loop-around temperature sensor measures temp up to 420 degrees F. Great for looping around motors.

NEW: The eLogger V3 supports up to two Hall Effects or Brushless RPM sensors! Up to three temperature sensors can be connected to the eLogger V3 simultaneously (two simultaneously for the V1/V2).

Requires: Eagle Tree Logger.