Dremel's 3/8" Flapwheel (80 grit) Accessory Bit.

Features: A wheel of 80 grit abrasive strips.
Flapwheels grind and polish flat or contoured surfaces.
Used most effectively as a finishing sander after heavier surface sanding and material removal is complete.
Use on surfaces such as metal, wood, rubber and plastic.
As the flapwheel wears down, new abrasive is continuously exposed,
preventing clogging and providing uniform finishing throughout the
life of the flapwheel.

Includes: One Flapwheel Bit

Requires: Rotary Tool

Specs:
Flapwheel Diameter: 3/8" (9.5mm)
Shank Diameter: 1/8" (3.2mm)

Dremel EZ Lock Abrasive Wheels.

Good for finishing props.

Features: Fits EZ402 mandrels used with Dremel rotary tools. Fine 320-grit rating for finish polishing.

Includes: Two Dremel Fine EZ Lock Abrasive Wheels

Requires: EZ402 mandrel. Installing on mandrel and fastening to rotary tool.

Specs: Height: 0.47" (12mm)
Diameter: 0.98" (25mm)

Dremel's 1/8" Tungsten Carbide Cutter Accessory Bit.

FEATURES

A high-speed cutter made of tungsten carbide, the hardest material
next to diamonds. Pointed tip. Ideal for shaping, smoothing or removing material from especially hard materials including hardened steel, stainless steel, cast iron, nonferrous metals, fired ceramics, plastics and hard woods. Use this bit at higher speeds for hard woods, slower speeds for metals, and very slow speeds for plastics.

Includes: One Tungsten Carbide Cutter

Requires: Rotary Tool

Specs: Cutter Diameter: 1/8" (3,2mm)
Shank Diameter: 1/8" (3,2mm)

Notes: Do not use this cutter for drilling holes or for enlarging holes that
are less than twice the diameter of the cutter. The tungsten
carbide surface can easily catch the side of a hole and break the
bit.

Dremel EZ Lock Mandrel.

Features: One-piece mandrel design simplifies the process of changing accessories-just pull, twist and release. For use with exclusive Dremel EZ Lock Accessories. Compatible with dremel rotary tools.

Includes: 1 Dremel EZ Lock Mandrel

Requires: Installing on rotary tool

Dremel EZ Lock Cutting Wheels.

Features: Easy installation-just pull, twist and release. Rated for metal cutting. Fits #EZ402 mandrel used with Dremel rotary tools.

Includes: Five Dremel EZ Lock 1 1/2 Cutting Wheels.

Requires: EZ402 mandrel. Installing on mandrel and fastening to rotary tool.

Spec: Diameter: 1.5" (38mm)

Dremel EZ Lock Cut-Off Wheels for metal cutting.

Features: Fits #EZ402 mandrel used with Dremel rotary tools. Easy installation-just pull, twist and release. Rated for metal cutting

Includes: Five Dremel EZ Lock Cut-Off Wheels

Requires: EZ402 mandrel. Installing on mandrel and fastening to rotary tool.

Specs: Diameter: 1.5" (38mm)

Dremel Coarse 36 Grit Detail Abrasive Brush. Good for sanding into tight corners.

Features: Coarse 36 Grit. Fits Dremel EZ402 Mandrels.

Includes: One Coarse 36 Grit Detail Abrasive Brush

Requires: EZ402 mandrel. Installing on mandrel and fastening to rotary tool.

Dremel Fine 220 Grit Detail Abrasive Brush from Dremel. Good for sanding into tight corners.

Features: Fine 220 Grit
EZ Lock Compatible
Fits Dremel EZ402 Mandrels

Includes: One 220 Grit Fine Detail Abrasive Brush

Requires: EZ402 mandrel. Installing on mandrel and fastening to rotary tool.

Dremel EZ Lock Cut-Off Wheels.

Features: Fits #EZ402 mandrel used with Dremel rotary tools. Easy installation-just pull, twist and release. Rated for plastic cutting

Includes: Five Dremel EZ Lock Cut-Off Wheels

Requires: EZ402 mandrel. Installing on mandrel and fastening to rotary tool.

Specs: Diameter: 1.5" (38mm)

Duratrax 32-Tip Multi-Driver

Includes the most-needed tips for working on R/C drones, park flyers and vehicles as well as watches, jewelry eyeglasses and more. Anodized aluminum handle holds 15 short-shank double-tip bits, another bit stores in the in-use position. Nine tip options for Torx (or "star") screw heads. Bit shanks lock onto the adjustable-length shaft with a push for easy attachment and release. Sizes clearly marked on each bit. Flattened handle design prevents rolling off of workbench.

Tip Sizes: (See picture 2)
Double-tip bits have two tips with the sizes indicated.
PH000 / 1.5 mm slotted.
PH00 / 2.0 mm slotted.
PH0 / 2.5 mm slotted.
PH1 / 3.0 mm slotted.
PZ0 / 3.5 mm slotted.
PZ1 / 4.0 mm slotted.
.050” hex / 0.7 mm hex.
0.9 mm hex / 1.5 mm hex.
2.0 mm hex / 3.0 mm hex.
2.5 mm hex / 4.0 mm hex.
3/32” hex / 1/16" hex.
T-4 / T-8 Torx.
T-5 / T-9 Torx.
T-6 / T-10 Torx.
T-7 / T-15 Torx.
1.0 mm slotted / T-20 Torx.

Great Planes Cut-Off wheels are for use with a Dremel tool or the like.

Features:
Large cutting edge for slotting and cutting. Fiberglass reinforced to help prevent breakage during use, adding saftey and strength.

Includes:
(1) cut-off wheel
(1) mandrel

Requires:
This requires a Dremel tool or similar product.

Specs:
Cut-off wheel diameter: 1-1/4"
Thickness: 1/32"
Mandrels shank diameter: 1/8"

NOTE:
Users and by-standers must wear safety glasses when using this product. This product is not to be used in excess of 28,000 rpm.

Great Planes Cut-Off wheels are for use with a Dremel tool or the like.

Features:
Large cutting edge for slotting and cutting. Fiberglass reinforced to help prevent breakage during use, adding saftey and strength.

Includes:
Two cut-off wheels in a reusable plastic parts pack.

Requires:
The cut-off wheels require a mandrel (GPMR8200) and a Dremel tool.

Specs:
Diameter: 1-1/4" diameter
Mounting hole: 1/8"

COMMENTS
Users and by-standers MUST wear safety glasses when using this product. This product is not to be used in excess of 28,000 rpm.

Keep your most-frequently used tools at your fingertips with the 12-in-1 Wrench Set from Kinexsis. Designed with most RC enthusiasts in mind this set contains the most-common hex and screwdriver sizes designed to lock into the included aluminum handle.

Includes:

.050”, 1/16”, 5/64”, 3/32” SAE hex tips
1.5mm, 2.0mm, 2.5mm and 3.0mm Metric hex tips
1.5mm slotted, 2.5mm slotted,
00 Phillips and 0 Phillips tip

10 in 1 Rc Tool kit
A great addition to the tool box. High grade tool steel with rubber coated handles for comfort. Precision sized allen drivers and screw drivers for non slip.

Kit Includes:

Wire cutters
Needle nose pliers
Ball link pliers
1.5mm, 2.0mm, 2.5mm Metric hex tips
#1 slotted screw driver
#0 Phillips screw driver
4.0, 5.5mm Metric Nut Drivers
 

Needle nose pliers with rubber grips.
 

Wire cutters with rubber grips.

Quick Tips Expert Tool Set

    1/4" drive stystem
    Most popular sizes for Metric sized hex-head screws and nuts used in 1/10th scale competition level vehicles
    Machine ground HSS (high speed steel) hex driver tips
    Tips are laser-marked with the hex size
    Red anodized aluminum handle with magnetic attachment system

Dynamite's Quick Tips Export Tool Set is compatible with just about any capable power drill or screwdriver. Speed up your wrenching time and lets you have more time at the wheel and on the track.

Includes:

    1/4" drive handle
    5mm nut driver (65mm long)
    5.5mm nut driver (65mm long)
    7mm nut driver (65mm long)
    8mm nut driver (65mm long)
    1.5mm hex driver (50mm long)
    2.0mm hex driver (50mm long)
    2.5mm hex driver (50mm long)
    Reusable pouch

 

Keep your most-frequently used tools at your fingertips with the Ultimate Air/Surface Startup Tool Set from Kinexsis. Designed with most RC enthusiasts in mind this set contains the most-common nut drivers, hex wrenches and screwdriver sizes designed to lock into the included aluminum handle. You won’t find a more comprehensive tool set out there. And to help you easily transport and protect your tools, we’ve included a convenient, durable pouch.

Includes
.050”, 1/16”, 5/64”, 3/32” SAE hex tips
1.5mm, 2.0mm, 2.5mm and 3.0mm Metric hex tips
1.5mm slotted, 2.5mm slotted,
00 Phillips and 0 Phillips tips
3/16”, 1/4”, 5/16”, 3/8" SAE Nut Drivers
5mm,5.5mm, 7mm and 8mm Metric Nut Drivers
3mm, 4mm, 5mm, 5.5mm, 6mm, 7mm, 10mm, 3/16”, 1/4”, 5/16” and 11/32” Box Wrenches

4-Way Wrench Steel

At OSE, we have modified this item to work with the standard 1/4"(14-28) and 3/16" (10-32) locking Zuber prop nuts. Normally the longer boat shafts will not fit all the way into these. These are drilled with both larger and deeper holes to be used on the rc boat shafts.

Note:
Works withose-zn-8135 ose-zn-1428 nuts
 

DBY Body Reamer

FEATURES
Super sharp cutting tip cuts and enlarges holes in Fiberglass, polycarbonate, ABS, balsa and other hobby materials. Fluted blade removes debris while cutting. Inlcudes screw on cap to help protect the blades.

INCLUDES:
(1) DBY Body Reamer

SPECIFICATIONS:
Cuts hole upto 14mm in diameter

Made For cutting of soft material and light gauge wire, these cutters will leave a near finished cut edge.

Duratrax Hole & Body Reamer

FEATURES
Super sharp cutting tip cuts and enlarges holes in polycarbonate, ABS, balsa and other hobby materials. Fluted blade removes debris while cutting. Large comfortable no roll design handle resists rolling off of workbench or pit table.

INCLUDES:
Duratrax Body Reamer

SPECIFICATIONS:
Total Length: 5.3" (135mm) including handle Blade Length: 1.6" (40mm)

This is a Dead Center Hole Locator for Locating Engine Mounting Holes.

Great Planes Dead Center Hole Locater is a tool that should be in every modeler's toolbox. The tool is extremely easy to use. Simply press its self- centering alignment cone into the mounting hole with the engine positioned on the motor mount, and give the handle a few turns, the sharp drill tip leaves perfectly centered marks every time!

INCLUDES: One dead center hole locating tool, with drill size guide on back of package. One clear protective plastic tube

SPECS: Tool is 6.75" in length to reach into cowls.

This is Hot Racing RC connector soldering Clamp jig.

FEATURES: Ideal for soldering and all types RC connector. This jig quickly and securely clamps, holds, and releases these connectors for your soldering tasks.

This Jig clamp holds the most common RC connectors
- XT60
- Deans T connector
- Traxxas TRX Connector
- EC-2
- EC-3
- EC-4
- EC-5
- Deans Micro 2pin to 4pin connectors
- Bullet connectors from 2 to 6.5 mm

Can be use as motor holder fit both 5mm and 1/8 motor shaft.

Includes:
(1) Hot Racing RC connector soldering Clamp jig.

NOTE:
Soldering tips:
1) soldering iron is must be very HOT!!!!
2) Tin the wire and the connector pin with good amount of solder.
3) Now place the wire and connector pin together with the help of a very hot soldering tip the solder will melts
4) Then remove the soldering tip from the solder join, and let it cool done.

Warning, The most dangerous is to connect positive and negative wires together creating a short circuit.
1) One of the wires must be properly isolated at all times.
2) Only clamp on one pin at a time from the same battery. DO NOT solder both positive and negative connectors in the jig at the same time. Doing so will cause a short circuit and possibly a fire or explosion.

Hot Racing Pro Connector Soldering Jig.

Holds most types of RC battery connectors in place for soldering to wires.

Holds XT60, Dean's T-connector, Traxxas connector, EC2-EC5, Dean's, Micro 2pin-4pin connectors and bullet connectors from 2-6.5mm.

Magnetic two piece design with alligator clips and solder storage. Two alligator clips style holding clamps for wire. Wide aluminum base for added stability. Can also be used as motor holder, fits both 5mm and 1/8" diameter shafts.

 This is a 2-56 Die from K&S Engineering.

A must for the scratch builder, modeler, etc. Rethreads 2-56 thread pattern. Intended for use on K+S Aluminum and Brass Stock

Includes: One 2-56 Die

Requires: dh-ks-420

Specifications:
Thread Pattern: 2-56
Diameter: ¾" (19mm)

Note: Use oil when cutting threads. Slowly cut the threads for the best results.
 

 This is a 4-40 Die from K&S Engineering.

A must for the scratch builder, modeler, etc. Rethreads 4-40 thread pattern. Intended for use on K+S Aluminum and Brass Stock

Includes: One 4-40 Die

Requires: dh-ks-420

Specifications:
Thread Pattern: 4-40
Diameter: ¾" (19mm)

Note: Use oil when cutting threads. Slowly cut the threads for the best results.
 

This is a Die Handle from K&S Engineering.

Holds dies securely during rethreading process. Fits up to 13/16" diameter dies

Includes: One Die Handle

Specifications
Length: 6½" (165mm)
Width: 1-1/8" (29mm)

Note: Use oil when cutting threads. Slowly cut the threads for the best results.
 

Click picture for video.
This is the EZ Bender Wire Forming Tool from Du-Bro. 1/16" to 3/32"

Features:
Works on .062" - .093" (1.6mm -2.4mm) diameter wire, see Notes.
Will bend wire from 0-90 degrees
Makes perfect Z-bends, L-bends and more

Includes: One EZ Bender Wire Forming Tool with instructions

Notes: Use with .062"-.093" (1.6mm -2.4mm) wire. Do not attempt to bend music wire (hardened wire) over .062" (1.6mm).

This is the K&S Wire Bender & Coiler.
Can be use to bend/coil Aluminum, Brass, Stainless Steel, & music wire

Features: Black steel construction

Includes: One base, One bending handle, One instruction sheet attached to top of box

Requires: When using, the base should be secured in a bench mounted vise

Specifications:

BASE HANDLE
Length: 2½" (64mm) 11½" (292mm)
Width: 1½" (38mm)
Height: 5/8" (16mm) Not including peg
Diameter: 11/16" (18mm)

Notes:
Will bend wire from 1/8" to ¼" (3mm-6.5mm) in diameter
Will coil wire 1/8" to 3/16" (3mm-4.5mm) in diameter

Cooper Tools SP40L Marksman 40 Watt Iron

Features:
• New indicator light allows you to instantly see that the iron is on.
• Fine quality mini iron, Measures 8-1/4"/210mm long.
• Lightweight pencil iron, ideal for hobbies
• MT10 1/4"/10mm diameter replaceable nickel-plated copper tip
• Develops 900°F/482°C temperature
• Stainless steel barrel and heat and impact resistant handle
• IMPORTANT: Use only Weller® tips.
• UL listed.

Weller Cooper Tools SP80 80 Watt Iron

Features:

High-Performance LED Soldering Iron - 80 Watts, up to 900-Degree F.
Three 5mm high temperature long-life LEDs at 25 Lumens/ft² for superior soldering accuracy and application illumination.
Co-molded soft grip ribbed handle design for maximum comfort and reduced slipage.
Triangular area for maximum of tip control. Round handle for ease of tip rotation.
Package Includes: Iron with MT620, 10mm tip, iron stand, user manual.

1 Pound of 1.5mm (.062") Diameter Lead Solder with Flux from Kester

INCLUDES:
Unit: POUND
Brand: Kester
Series: 44 Core
Type: Activated Rosin Flux Core
Wire Diameter: 0.062 in

COMMENTS
Flux is a hazardous flammable liquid that requires ground shipping. LEAD is hazardous to health. Handle with care.
 

 This is 3/64" Diameter 1/2oz Silver Solder with 1/2 oz Flux from Stay-Brite.

FEATURES

Five times stronger than ordinary solder with tensile strength of
10,000-25,000 pounds per square inch.
Will stretch under high pressure, but not break under constant stress
and is vibration-resistant.
Lead free making it environmentally friendly
Melts and flows at 430°F, providing strength without distortion

INCLUDES

One 3/64" Diameter, 1/2oz Silver Solder Coiled
One 1/2oz Bottle of Flux
One Instruction Sheet
One Clear Plastic Storage Canister with White Lid

COMMENTS

NOT for use with electronic applications
Flux is a hazardous flammable liquid that requires ground shipping

DuraTrax Flashpoint Infrared Temperature Gauge.

Point and click! That's all that it takes to figure out the temperature of your brushless motor, nitro engine, esc or batteries. This is a tool every electric or nitro hobbyist should carry in their tool box!

Etti propeller balancer. Aluminum and stainless steel construction.
Can balance up to a 4.5" propeller!

Includes 3 different adapters to balance the following propellers.

-3/16" propellers.
-1/8" propellers.
-M4 / 4mm threaded propellers.

Click picture for more details.

Aluminum and stainless steel construction.
Can balance a propeller up to 82mm in diameter!

Includes shafts and adapters to balance most of the varieties of props on the market! Eight different sizes in total!

*Propeller in picture not included!

The Top Flite balancer is an innovative way to balance your aircraft or boat propellers, spinner backplates, car wheels and tires, as well as many other items in the hobby industry.

Precision ground balancing shaft, held between two powerful "Ceramic 8" magnets allows shaft to "float" for maximum sensitivity Inexpensive and easy to use...essential for every modeler. Reduces prop vibration-reducing engine wear and prevents structural damage Can be used anywhere-on the workbench or at the field Constructed of long-lasting, high impact plastic and nickel steel Includes instructions explaining how to correct out-of-balance props, and even how to use the balancer to determine wind speed. Can also be used to balance boat props, car wheels and tires, ducted fans, spinners, nose weights and more! Balances up to 24" propellers and any size wheels and tires.

This prop balancer has an extruded aluminum base and two parallel steel rods for the pro shaft to roll on. It comes complete with a leveling screw and three prop shafts (1/4", 3/16" & 1/8") which store within the unit. Basic instructions are included.

REQUIRES:
Dust mask, Eye protection, small files and sandpaper.

This is a Metric Set of Eight Commonly Used Hex L-Wrenches.

FEATURES: High-Grade Chrome Vanadium Steel Hardened Blades Ball Ends to Allow for Tight Spaces Turns 360° at Entry Angle up to 25°

INCLUDES: Eight Wrenches: 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm Handy Blue Carrying Case for All Wrenches with Size of Wrench Marked on the side for Easy Identification.

This is a Eight Piece Set of Standard L-Wrenches.

One End of the Wrench has a Ball to Allow for Entry Angles up to 25°.

FEATURES: Perfect Sizes for Hobby Uses Turns 360° with a 25° Entry Angle. High-Grade Chrome Vanadium Steel

INCLUDES: Eight Wrenches: .050", 1/16", 5/64", 3/32", 7/64", 1/8", 9/64", 5/32". Handy Red Carrying Case for All Wrenches with Sizes Marked On Case.

5 pc Metric Hex Driver Assortment

Set Includes: 1.5, 2, 2.5, 3 and 4mm

5 pc Std Hex Driver Assortment

Set Includes: .050, 1/16, 5/64, 3/32 and 7/64

Quality anodized handle & replaceable tips.

Set Includes: .050",  1/16",  3/32"

.050 Hex driver with quality anodized handle & replaceable tips.

1/16" Hex driver with quality anodized handle & replaceable tips.

5/64" Hex driver with quality anodized handle & replaceable tips.

3/32" Hex driver with quality anodized handle & replaceable tips.

Quality anodized handle & replaceable tips.

Set Includes: 1.5mm,  2.0mm and 2.5mm drivers 
 

1.5mm Hex driver with quality anodized handle & replaceable tips.

2.0mm Hex driver with quality anodized handle & replaceable tips.

2.5mm Hex driver with quality anodized handle & replaceable tips.

3.0mm Hex driver with quality anodized handle & replaceable tips.

Click picture for full details.

This is a great test tool to find how many amps your system is drawing or testing cells and much, much more. It connects between the battery pack and load to measure volts, amps, watts and amp hours.

Measures 8 parameters key to electric power safety & performance, typical applications:
 * to prevent peak currents damaging battery, motor control, motors, wiring and connectors.
 * Verify sufficient operating voltage under load.
 * Set cutoff voltages, check battery capacity & health.
 * Balance battery cells.
 * Confirm proper battery charger operation.
 * Detect receivers and actual operating current so as to make sure whether an UBEC is needed.

GPS Speed Meter

Dynamite's GPS Speed Meter and Tracker provides car/truck, boating and air enthusiasts with a compact, portable and easy to use GPS device for tracking everything from top speed reached to locations of their model. The unit's compact size and ultra light weight allows for it to be utilized in various applications including everything from large scale aircraft to 1/10th or smaller radio control cars/trucks/boats.

Thanks to the units built-in WASS/EGNOS/MSAS/RTCM (Global Positioning compatibility by country or region), the unit can be used anywhere in the world. The unit uses 10Hz refresh rate providing extremely fast response to changes in the models position while the units low power consumption provides the user with up to 4 hours of uninterrupted tracking time.

The unit's LCD screen provides real-time data feedback and it's waterproof design allows for use in virtually all weather conditions. You can also use the Dynamite GPS Logger* software to map your drive, flight, jog, swim, etc. using Google mapping products.

The LCD screen will display average, current, and peak speed. As well as current and max altitude, total distance, and GPS coordinates.

Features:
Track: Location, speed, altitude and much more.
Compact size allows for fit easy almost anywhere.
Lightweight for almost any RC application.
Built-in high-capacity LiPo Battery - 4 hours cont. tracking.
USB cable included for charging.
PC Interface for mapping on Google map products.
Can be used in real-world application worldwide.
Reads speeds up to 560 MPH (900 KPH).
Switch between Metric and Imperial units using PC software.

This is used when OSE does custom work for an order. But 1 item for each dollar needed for labor/work.

For example. If something will cost $20.00, buy 20 of these.

Please do not use this unless you speak to us first about the costs.

This is used when OSE does custom work for an order. But 1 item for each dollar needed for labor/work.

For example. If something will cost $20.00, buy 20 of these.

Shipping fee's are applicable with this item.

Please do not use this unless you speak to us first about the costs.